Madison, NJ's Expert Plumbing & HVAC Repair Contractor

We received a call from a customer in Madison, NJ who had an older failing steam boiler. Our system design specialist recommended a Crown steam boiler as a replacement. The system was adapted to the existing steam piping, gas line, and electrical lines. The technicians replaced the 2 main return vents next to the boiler. He also replaced 3 radiator vents in the home and one in the den, as well as the daughters room. The electrician helped to remove the old boiler and piping, as well as the electric conduits and wire.  They turned the system on and tested to make sure everything was working properly before leaving the residence, Now the home owner has peace of mind knowing that thier new system will bring them comfort and reliability for the coming winter months. 

We recently got a call from a customer that needed lighting in their basement for the laundry area. We sent out or electrician to take a look at the current wiring. The customer would like to replace the ceiling fixture in his laundry room with a 4’ fluorescent fixture.  He spoke with him about options and the home owner agreed that he should install a 4’ LED fixture instead,  this will provide better lighting and more reliability over the older style fluorescent lights. The laundry area is now much brighter and the customer is very happy. 

We received a call from a customer who was experiencing issues with a circuit in their kitchen. We sent an electrician out to diagnose the problem. After the work was completed, the customer asked for him to look at the kitchen outlets and see if he could split up the wiring.  She had two outlets, one on each side of the sink and both are on the same circuit and 15 amp circuit breaker.
The technician looked over what would be involved and made an estimate for her to add a new circuit and replaced the existing circuit breaker with a properly sized 20 and unit.

The electrician ran a new 20 amp circuit and fished it to the outlet box to the left of the window.  He disconnected the old wire feeding it and capped it of in the box. The existing circuit  was wired back to the panel, he then increased the circuit breaker size to 20 amp.

We received a call from a customer who said she heard a gurgling noise in her drains and noticed water leaking form a basement pipe. Upon arrival the tech found that the trap clean out cap was dripping and pressurized. He opened slowly to not let the water rush out too fast. Customer was concerned not to flood the basement.  After the water slowed down we attempted to clear the trap and it was unsuccessful due to heavy amounts of build up within the trap. The tech recommend removing the trap and will diagnose if the rest of the line is clear. 

An unreliable heating system prompted the customer to call us for a free estimate for a Lennox gas furnace replacement. Our technicians went to the home to install a new furnace. The technicians removed the old furnace and put the new system in place. They reconnected the gas flu pipe end humidifier to make sure everything was working correctly. The electrician connected the wiring for the I-comfort thermostat. He tested the equipment and set the schedule to run as requested by the customer. Additionally he filled out chimney certificate for the customer. Now the home owner will have comfort throughout the home and also lower utility bills with a new more efficient heating system. 

The customer stated the master bedroom zone is not cooling down. Upon diagnosis the technician found the master-bedroom zone low on charge, discussed with customer options on potential repair, customer opted for basic system charge. He charged the master bedroom system with up to 4 lbs of refrigerant, be aware issue could present itself again in the future due to such high amount of refrigeration required to operate system. He also performed a routine AC Maintenance on the other two systems. The tech checked the refrigeration levels, outdoor electrical, cleaned indoor filters, cleaned condensate trap and poured bleach down trap.

Our electrician arrived at the job to rebuild electrical system for pool equipment area. He labeled all of the old wiring and removed electrical panels and outlet. The he disconnect wiring from the pool control box. The junction feeders for the pool panel and pipe over to the new panel location. He mounted a new panel on the stone wall, higher and away from obstructions. He extended the wiring and wire panel. He then ran a new conduit from panel to pool control and the new circuits. The electrician removed the old wiring and connected new circuits to control relays. He ran a conduit from panel to new service outlet, switch and light over the equipment area. He installed an outlet for the antennae and removed 1 pool niche light and put in new customer supplied light.

Upon arrival our technician met with the homeowner to discuss the issues and help to solve his problems. The customers thermostat was malfunctioning. Upon further inspection system was low on refrigerant and additional issues. Our production manager, Jose was on site to help resolve the issues. The issue was very minor and he showed the customer how to use the thermostat properly.

Upon arrival our technician met with the homeowner. He performed an inspection of the 2nd floor toilet and spoke with management and installed new a new flapper. The tech performed a maintenance check up on a 4 year old air conditioning unit and found some concerns, then provided options to owner. At this time the owner chose to supply refrigerant and administer UV dye to balance system, allowing proper cooling. UV dye will allow us to locate any leaks in the future. We will replace schrader cores to ensure no issues and chemically clean outdoor evaporator to keep compressor running at proper temperatures.

The customer needed maintenance on system and filter replacement. Our technician went to the home to perform the filter replacement. He also took a delta reading of indoor unit while running for a 17 degree split. 

Our technician went to a home to remove an old system and install a new water treatment system. He removed the existing halo and installed a new whole home water treatment to address the softness and chlormines in house. This installation includes all piping and discharge for complete install. He drained the home and removed the existing system. The technician installed a new whole home water treatment with all required piping to restore usage to the home.

When our technician went to the customers home to diagnose, he found the system and electrical components damage by a critter. He spoke to the home owner and he authorized the electrical component repair. After further testing it showed the system was flat on refrigerant which indicates a significant leak. He proceeded to pressure test system with nitrogen and found leak to be coming from outside filter drier, filter drier shattered and refrigeration leak was emptied out. After speaking to the customer and advised him of the repairs, he suggested to replace outdoor condensing unit and indoor equipment seemed adequate still.

Our electrician went to the customer's home to rewire a new condenser to existing wiring. He also removed the old wiring from the attic furnace. He also installed new wiring and a service switch, to wire to the furnace. The electrician replaced a stat wire to outdoor condenser, existing is 2 wire, new condenser in communicating. He fished new line over a vaulted ceiling and into attic space, then used 6 conductor cables. 

Our technician performed a cooling PSA. Indoor unit air filter is in clean condition and has been recently replaced by the homeowner. Also found indoor electrical circuits and components working properly at this time. No issues with airflow. Drain has been cleaned. Proper delta teeacroos evaporator coil. 
Outdoor unit electrical circuits and components working properly at this time as well. Refrigerant charge within manufacturer  specs with 60 degree ambient.

Our plumbing technician arrived onsite to replace hot side shut off valve in a powder room off the kitchen. The customer also asked for a quote to replace the faucet. He told him the quote for the faucet and pop-up that he received on Saturday was the quote and also gave another quote to replace the faucet and pop-up as well as remove the flex tailpiece. The brass trap and replaced with a new trap and tailpiece.

Our plumbing technician arrived onsite for a leaking urinal. After several flushes he found a small leak coming from urinal outlet. He pulled urinal and found wax with build-up on it. Removed wax and snake line with small handheld machine to removed build-up from line. He placed a new wax on hanger and rehung urinal. Then he turned water on to flushometer and set pressure. The technician flushed several times and tested for leaks and proper operation.

The technician found valve handle loose as well customers complain on master bedroom not getting heat. He tested the unit and identified zone as well label zone. It was not responding to the  thermostat and he replace zone valve head.

Open 1 ft section of the basement/bathroom drywall ceiling below the kitchen.

-Spray Foam the rim joist with 2 inches of closed cell spray foam to air seal and insulate.

-Dense Pack the kitchen walls with Trusoft cellulose- “attempt to dense pack from the balloon framing opening in the basement area”

-Patch all holes created with drywall and 1 coat of drywall joint compound. 

-Patch living ceiling hole left when radiator was repaired.

Pipe Works Services will cover and protect all areas where work is being performed.

Clean up and dispose of all debris in the crawlspace.

-Install a Terrablock foam board insulation through out the entire crawlspace.

-Install a 20 mil poly vapor barrier over the entire crawlspace floor.

- Install 2 inch silver glo foam board insulation on all the exterior walls. 

-Spray foam all accessible rim joist with 2inch Closed Cell spray foam.

Pipe Works Services, Inc. will remove sections of the vinyl soffit on the underside of the roof in the following locations :

- the front of the house
- the entire left side of the house
- the right side up to where the roof meets the covering of the entrance.

Pipe Works Services Inc. will also remove the vinyl soffit on the underside of the overhang above the garage entrance at the front of the house.

Pipe Works Services Inc. will install foam insulation to air seal all accessible opening to the best of our ability, to prevent air infiltration.

Pipe Works Services Inc. will re-install the removed sections of the vinyl soffit.

Pipe Works Services Inc. will remove sections of the vinyl siding on the wall above the garage at the front of the house. We will drill 2-9/16" holes between the studs of the wall. 

Pipe Works Services Inc. will dense pack our TruSoft Cellulose Insulation through the drilled holes, filling the cavities of these spaces between the studs.

Pipe Works Services Inc. will plug the drilled holes and seal air and water tight.

Pipe Works Services Inc. will re-install the removed sections of the vinyl siding.

Pipe Works Services, Inc. will drill 2-9/16" holes between the joists of the garage ceiling.

Pipe Works Services Inc. will dense pack our TruSoft Cellulose Insulation through the drilled holes, filling the cavities between these bays.

Pipe Works Services Inc. will plug the drilled holes and apply some joint compound to seal it air-tight. Please note that Pipe Works Services Inc. will not be responsible for painting or repainting, nor liable for the costs or any related charges.

Remove and dispose of existing fiberglass and debris in crawl space. Supply and install CleanSpace Crawl encapsulation with 2'' Silverglo bolted and air sealed to side walls 1" TerraBlock insulation on floor covered with cleanspace vapor barrier liner. Reduce heat loss and infiltration of cold air by sealing and insulating the Rim Joist area with approximately 2" closed-cell polyurethane spray foam insulation. 

Upgrade 2'' x 4'' wall insulation with dense-packed TruSoft cellulose insulation by drilling through the shingle and sub-wall dense packing each joist bay with cellulose then plugging all holes with a cedar wood plug and sealing with foam or caulk. This includes all of the exterior walls on the first floor and the back and two side walls of the second floor. Shingles will not be replaced as new siding is being installed by others at no cost to Pipe Works Services. 
Insulate and air seal ceiling over garage with dense-pack TruSoft cellulose insulation - ceiling bays accessed from inside of the garage by drilling multiple 2 1/4" holes in the Sheetrock ceiling dense packing each joist bay with TruSoft cellulose then plug and patch all holes with one coat of Spackle. We will repair the sections of Sheetrock that have been cut out on the left side of the garage.

Apply approximately 3" Closed cell spray foam to over hang of master bedroom and band joist associated with over hang.

Install 'SuperKneeWall' upgrade by bolting 1" Thermax fire rated insulated foam board to rafters then air sealing all seams with one part spray foam in both knee walls off master bedroom and attic above sun room. Entry to the knee wall is through a blank vent cover. All open access ponts will be closed off with 1/2" sheetrock tape and one coat of spackle. Paint is not included.

Install 'SuperKneeWall' by cutting access in sheetrock wall in guest room closet at front of house over entry way then bolting 1" Thermax fire rated foam board insulation to rafters and air sealing all seams. Access will be closed up with 1/2" sheetrock taped and one coat of spackle. Paint is not included.

Remove and dispose of existing fiberglass insulation in attic.
Air Seal and Insulate 'traditional' attic by closing all accessible penetrations and top plates using expanding polyurethane foam and then blowing in approximately 14" R49 TruSoft cellulose including plywood retention dams around attic hatch.

Install 'SuperKneeWall' upgrade by bolting 1" Thermax fire rated insulated foam board to rafters then air sealing all seams with one part spray foam in both knee walls off master bedroom and attic above sun room. Entry to the knee wall is through a blank vent cover. All open access ponts will be closed off with 1/2" sheetrock tape and one coat of spackle. Paint is not included.

Install 'SuperKneeWall' by cutting access in sheetrock wall in guest room closet at front of house over entry way then bolting 1" Thermax fire rated foam board insulation to rafters and air sealing all seams. Access will be closed up with 1/2" sheetrock taped and one coat of spackle. Paint is not included.

Remove and dispose of existing fiberglass insulation in attic.
Air Seal and Insulate 'traditional' attic by closing all accessible penetrations and top plates using expanding polyurethane foam and then blowing in approximately 14" R49 TruSoft cellulose including plywood retention dams around attic hatch.

PIpe works Home Services installed the folloing in a home in Madison, New Jersey.

3 Ton 4SCU13LE1 Armstrong Condensing Unit
Armstrong Modular Air Handler
Aprilaire Thermostat
*New Electrical Whip and Disconnect
*New condenser pad

Pipe Works Services received a call from an existing customer in Madison, NJ about a boiler tune up. This customer wanted to be proactive and wanted to prepare for the upcoming fall and winter months. Luckily Pablo was the right technician for the job. Pablo was dispatched and went to the customers house to perform a through inspection and cleaning. Pablo cleaned the burners for the boiler which is the central element that makes the heat, cleaned boiler sediment out, then tested auto feed which maintains a safe water line for the boiler. Pablo cleaned the flame rod where the flames reach the boiler and tested system for proper operations and function system is running properly. This boiler was installed by Pipe Works 2 years ago. 

Pipe Works Services received a call from a customer in Madison, NJ about their air conditioning not turning on. Pipe Works technician Zach arrived to home to diagnose the cause of AC not engaging. Zach found the overflow safety switch to be tripped. Dried off the switch and reset it. The unit engaged.  Cleared out condensate drain line and tested it. There was a small obstruction in the line but since clearing it, water flowed normally. This is likely the cause I'd Raised up the overflow switch and put it back in the pan. Zach discovered that the coil pan was indeed cracked and leaking which is causing water to fill secondary pan. Our customer was provided estimate from Rob and our technicians Nick, Odin, Ramito and Ryan installed a 4 Ton XC16 Lennox Condensing Unit, CBX32MV Lennox Air Handler with a Lennox iComfort Thermostat.